• -25%
FIBARO - Motion Sensor Z-Wave+ FGMS-001
search
  • FIBARO - Motion Sensor Z-Wave+ FGMS-001
  • FIBARO - Motion Sensor Z-Wave+ FGMS-001
  • FIBARO - Motion Sensor Z-Wave+ FGMS-001
  • FIBARO - Motion Sensor Z-Wave+ FGMS-001
  • FIBARO - Motion Sensor Z-Wave+ FGMS-001

FIBARO - Motion Sensor Z-Wave+ FGMS-001



FGMS-001-ZW5
€76.02
€57.02 Tax included Save 25%

The FIBARO Motion Sensor is a highly advanced, ultra small multi-sensor.

Quantity

 

Security guarantees

 

Shipping Policy

The FIBARO Motion Sensor is a highly advanced, ultra small multi-sensor. Motion Sensor honored with CES 2015 Innovation Awards and International Design Awards 2015. This tiny sensor has a built-in temperature sensor, light sensor and accelerometer. The eye of the sensor shines with user-defined colors to visually alert when detects motion and alarm. The Motion Sensor is completely wireless and mobile. It can even turn the lights on when you enter that room!

How often does it happen that one of family members forgets to turn off the light? Motion Sensor integrated with lighting system is a simple way to save the energy. Lamps will automatically turn on when someone enters the room and turn off when no movement is detected.

Children during their innocent plays may become a reason of minor damages at your home. How to protect your jewellery, important documents or expensive cosmetics from their creativity? Motion Sensor is a small device which will take care of your valuables. When the sensor detects movement in the room, the information will be sent to your phone. It is your decision what actions should be taken later.

Your child does not like to fall asleep when it is dark in the room? Thanks to Motion Sensor there will be no need to get up and turn off the lamp in a child's room. The sensor will turn off the light automatically after the child falls asleep and stops moving in the bed.

Are you worried that your child will wake up at night and wander around the house unattended? Motion Sensor will send you a notification whenever motion is detected in the hallway at night.

Motion Sensor turns on the lights in the room when motion is detected, but only if it is necessary. Built-in light sensor allows the device to distinguish day from night. Lamps will be turned on only after sunset or on a cloudy day.

FEATURES :

  • Plug and Play extremely easy installation on surface without drilling and cabling
  • Detects every motion and allows lighting controls and heating measuring
  • Possibility to Integrate with alarm or fire prevention system
  • Measures the temperature
  • Compatibles with any Z-Wave controller
  • Alarms of movement and temperature are signaled by LED diode blinking
  • Simple earthquake detector mode

TECHNICAL DATAS :

  • Wireless technology: Z-Wave
  • Power: CR123A Battery
  • External Power: 12-24 VDC
  • Output Terminal Voltage: 40V (AC or DC) max.
  • Output Terminal Current: 25mA max.
  • Measure Temperature: -20 to +100°C
  • Dimensions (diameter x height): 72 x 28mm

FGMS-001-ZW5
æ 2024-08-05

Data sheet

Type
Sensor
Functions
Luminosity
Motion
Temperature
Vibration
Technology
Z-Wave Plus
Power Supply
Battery
Compatibility
Eedomus
Fibaro HC3
Fibaro HC3 Lite
Homey
Jeedom

Procedure for resetting the FIBARO Motion Sensor:

1) Make sure the battery is not discharged and properly in place in the case.

2) Press and hold button B for 4-6 seconds until the LED illuminates yellow signaling the 2nd option in MENU mode.

3) Release button B.

4) Briefly press button B again. Successful reset will be confirmed by the LED changing to red color before it turns off.

Notes:

  • There is only one way to reset the FIBARO Motion Detector. The procedure erases the detector's memory including data relating to the main controller and the Z-Wave network.
  • Resetting the device will not delete the device from the Z-Wave main controller memory.
  • Removing the device from the Z-Wave network will automatically reset FIBARO Motion Detector.
Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

When you are in the Z-Wave network range test mode, the LED indicates the status of the Z-Wave communication.

FLASHING GREEN – The sensor is attempting to establish direct communication with the main controller.

GREEN – The detector is in direct communication with the main controller.

FLASHING YELLOW – The sensor is trying to establish communication with the main controller via other modules.

YELLOW – The detector is in indirect communication with the main controller.

FLASHING PURPLE – The sensor is communicating with the controller at the controller's range limit.

RED – The detector cannot connect to the main controller, either directly or through other nodes in the Z-Wave network

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

To enter the MENU, press and hold button B for at least 3 seconds.

The MENU levels will be indicated by the different colors of the LED:

PURPLE - Z-Wave network range test

YELLOW – Detector Reset

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

1. How to reset battery power level

Please change the time interval between two alarm clocks in the Z-Wave controller settings.

2. Temperature and brightness reports are sent too frequently to the controller.

Please change the time interval between two reports with Advanced Settings No. 40 and No. 62.

3. The associated devices or the main controller of the Z-Wave network is no longer powered. The detector unsuccessfully attempts to reconnect to these devices.

Check power and connection of other Z-Wave devices. Remember that all electrical work must be carried out by a qualified electrician.

4. FIBARO Motion Sensor sends false alarms.

The sensitivity of the FIBARO Motion Sensor is adjustable. Please check the values of Advanced Settings No. 1 2 3 4.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

1. The battery is almost discharged.

Replace the battery by opening the housing cover. Then close the case and put it back in place.

2. The FIBARO Motion Sensor is out of range of the Z-Wave controller.

The FIBARO Motion Detector is out of range of the Z-Wave controller. It must be within direct range of the Z-Wave controller or within range of another node on the Z-Wave mesh network.

3. FIBARO Motion Sensor has been reset.

After resetting the FIBARO Motion Sensor, it returns to its default settings. To use it, you must again make the inclusion to your Z-Wave controller.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

1. The battery is almost discharged.

Replace the battery by opening the housing cover. Then close the case and put it back in place.

2. The FIBARO Motion Sensor is placed too close to a light source.

The FIBARO Motion Sensor must be placed in a place where you want to detect movements and where you can read a reference brightness. Avoid locations exposed to a direct light source.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

1. The battery is almost discharged.

Open the case of the device, replace the battery with a new one, close the case and replace it in its location.

2. The FIBARO Motion Sensor does not signal that it has a new battery.

Please wait for FIBARO Motion Sensor to wake up or manually wake it up by pressing button B on the device. Then close the case and put it back in place.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

The value of Advanced Parameter No. 80 has been modified.

Please set Advanced Parameter No. 80 = 10.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

1. The value of Advanced Parameter No. 80 has been changed.

Please set Advanced Parameter No. 80 = 10.

2. The battery is almost discharged.

The FIBARO Motion Sensor must be powered. Check if your detector is receiving power by opening the housing cover and checking the battery. Then close the case and put it back in place.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

The FIBARO Motion Detector can control up to 5 standard devices and 5 multi-channel devices for each association group.

Add up to 5 Z-Wave devices to an association group.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

1. The FIBARO Motion Sensor is no longer powered.

The FIBARO Motion Sensor must be powered. Check if your detector is receiving power by opening the housing cover and checking the battery. Then close the case and put it back in place.

2. FIBARO Motion Sensor has been reset.

After resetting the FIBARO Motion Sensor, it returns to its default settings. To use it, you must again make the inclusion to your Z-Wave controller.

3. The FIBARO Motion Sensor is out of range of the Z-Wave controller.

The FIBARO Motion Sensor is out of range of the Z-Wave controller. It must be within direct range of the Z-Wave controller or within range of another node on the Z-Wave mesh network.

4. The battery is almost discharged.

Replace the battery by opening the housing cover. Then close the case and put it back in place.

5. The FIBARO Motion Sensor is damaged

Please contact your dealer to initiate the warranty procedure for your FIBARO Motion Sensor.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

1. The FIBARO Motion Sensor is no longer powered.

The FIBARO Motion Sensor must be powered. Check if your detector is receiving power by opening the housing cover and checking the battery. Then close the case and put it back in place. Before using the FIBARO Motion Sensor, remember to remove the "I'm ready" tab.

2. FIBARO Motion Sensor has been reset.

After resetting the FIBARO Motion Sensor, it returns to its default settings. To use it, you must again make the inclusion to your Z-Wave controller.

3. The FIBARO Motion Sensor is out of range of the Z-Wave controller.

The FIBARO Motion Sensor is out of range of the Z-Wave controller. It must be within direct range of the Z-Wave controller or within range of another node on the Z-Wave mesh network.

4. The FIBARO Motion Sensor is damaged

Please contact your dealer to initiate the warranty procedure for your FIBARO Motion Sensor.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

1. The FIBARO Motion Sensor is placed too close to a heat source.

The FIBARO Motion Sensor should be placed where you want to detect movement and where you can take a reference temperature. Avoid locations near a heat source.

2. Advanced Parameter #66 has been changed.

Parameter No. 66 of the FIBARO Motion Sensor allows the compensation of the temperature detected. Check that parameter No. 66 = 0

Remember that the temperature measured behind a window is not the same as in the center of a room.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

The battery is almost discharged.

Open the case of the device, replace the battery with a new one, close the case and replace it in its location.

The FIBARO Motion Sensor does not report that it has a new battery.

Wait for FIBARO Motion Sensor to wake up or wake it up manually:

a) open the device and press button B.

e) close the cover and replace the sensor.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

1. FIBARO Motion Sensor is already included in another Z-Wave controller.

FIBARO Motion Sensor must be deleted using the Z-Wave controller or must be reset as follows:

a) open the cover of the device,

b) press and hold button B until the LED turns yellow.

c) release the button and press again.

d) close the cover and replace the sensor.

2. The FIBARO Motion Sensor is too far from the Z-Wave controller.

The FIBARO Motion Sensor must be within direct range of the Z-Wave controller during the inclusion process.

3. The FIBARO Motion Sensor is not powered.

The FIBARO Motion Sensor must be powered. Check if your detector is receiving power by opening the housing cover and checking the battery.

Then close the case and put it back in place.

Before using a FIBARO Motion Sensor, remember to remove the "I'm ready" tab.

4. The FIBARO Motion Sensor has a different frequency (EU, US, or ANZ) than your Z-Wave controller.

The FIBARO Motion Sensor must operate on the same Z-Wave frequency (EU, US, or ANZ) as your Z-Wave controller. Please contact your dealer to exchange it.

5. The FIBARO Motion Sensor is damaged

Please contact your dealer to initiate the warranty procedure for your FIBARO Motion Sensor.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

The range of the sensor can be influenced by the environment. Check for moving objects within the sensor's detection angle, such as the movement of tree branches in the wind or passing cars. False motion alarms can be caused by moving air masses and/or hot air.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

If the battery is draining quickly, please check the following parameters which can influence the life of your battery:

• Wake-up intervals too short – it is recommended to lengthen this interval.

• Timeout for sending temperature and light intensity measurement reports too short – change the Advanced Settings to decrease the frequency of sending reports.

• If associated devices or the main controller of the Z-Wave network lose power, the sensor will too often attempt to reconnect to these devices in vain; which will result in shortened battery life.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

No, it is for indoor use only.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

The actual range of the detector may be influenced by its surroundings, but it can be up to 7 meters. His angle of view is very wide.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

You must adjust the insensitivity time of the motion sensor using parameter 2. After this period of time, the PIR detector will detect a new movement.

The longer the insensitivity period, the longer the life of your battery. If you want the detector to detect any movement quickly, you can decrease this time.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

Parameter 80 determines how the LED reacts after motion detection.

Value between 1 and 9 = single long flash at the moment of motion detection. No further movement will be reported until the alarm is cancelled.

Value between 10 and 18 = single long flash when motion is detected and one short flash each time another motion is detected during alarm.

Value between 19 and 26 = single long flash when motion is detected and two short flashes each time another motion is detected during alarm.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

Parameter 8 determines the period of activity of the PIR sensor during the day.

This setting only affects motion detection reports and associations. Measurements of light intensity, temperature and sabotage detection will always be active, regardless of this setting.

0 – PIR sensor always active

1 – PIR sensor active during the day only

2 – PIR sensor active at night only

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

The sensitivity of the FIBARO Motion Sensor can be modified using the first parameter. The lower the value, the more sensitive the PIR sensor will be.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

You can choose to add or subtract a value to the actual temperature measured by the sensor (temperature compensation) using parameter 66.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

It is very simple. The FIBARO Motion Sensor can be configured to work as an earthquake detector by setting the value of parameter 24 to 4.

Reports about vibrations will be sent to the controller at the time intervals specified in parameter 22.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

No, it cannot be mains powered. The detector does not have connectors to connect it to the mains.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

You might also like