• -25%
FIBARO - Smart Module
search
  • FIBARO - Smart Module

FIBARO - Smart Module FGS-214



FGS-214
€79.20
€59.40 Tax included Save 25%

FIBARO Smart Module is designed to be installed in standard wall switch boxes or anywhere else where it is necessary to control electric devices.


10 Products available
Quantity

 

Security guarantees

 

Shipping Policy

  

The remotely operated FIBARO Smart Module is designed to turn an electrical device or circuit on and off. The compact size of the device allows for the product to be installed in the housings of other devices. FIBARO Smart Module can be controlled either via the Z-Wave network or with a button connected directly to it.

FEATURES :

  • Compatible with Z-Wave or Z-Wave+ Controller
  • Supports protected mode (Z-Wave network security mode) with AES-128 encryption
  • Advanced microprocessor control
  • Single channel dry contact switch
  • Works with various types of switches – momentary, toggle, three-way, etc
  • To be installed in wall switch boxes of dimensions allowing for installation, conforming to provisions of applicable regulations

TECHNICAL DATAS :

  • Power supply: 100-240V~ 50/60 Hz
  • Rated load current: 6,5A (resistive load only)
  • Operational temperature: 0-35°C
  • For installation in boxes: Ø ≥ 50mm, depth ≥ 60mm
  • Radio protocol: Z-Wave (500 series chip)
  • Radio frequency: 868.4 MHz
  • Range: up to 50m outdoors up to 40m indoors (depending on terrain and building structure)
  • Dimensions (L x W x H): 42.5 x 38.25 x 20.3 mm
  • Comply with EU directives: RED 2014/53/EU RoHS 2011/65/EU

FGS-214
10 Items

Data sheet

Type
Micromodule
Functions
Actuator
Dry Contact
Technology
Z-Wave Plus
Power Supply
12/24VDC
Main power
Compatibility
Eedomus
Fibaro HC3
Fibaro HC3 Lite
Jeedom
Z-Wave specificity
Security S2
SmartStart
View the trust certificate
  • For further information on the nature of the review controls, as well as the possibility of contacting the author of the review please consult our Transparency Charter.
  • No inducements have been provided for these reviews
  • Reviews are published and kept for a period of five years
  • Reviews can not be modified: If a customer wishes to modify their review then they can do so by contacting Verified Reviews directly to remove the existing review and publish an amended one
  • The reasons for deletion of reviews are available here.

4.4 /5

Based on 8 customer reviews

  • 1
    1
  • 2
    0
  • 3
    0
  • 4
    1
  • 5
    6
Sort reviews by :

Alexandre M. published the 03/11/2023 following an order made on 26/10/2023

1/5

Déçu, pas de retour d’état en commande local (entrée S1 ou S2) sur jeedom, alors que ça fonctionnait très bien avec le FGS-212

Did you find this helpful? Yes 0 No 0

Anonymous customer published the 27/12/2020 following an order made on 15/12/2020

5/5

Intégration facile avec Jeedom Smart. Fonctionne très bien.

Did you find this helpful? Yes 0 No 0

Anonymous customer published the 09/12/2020 following an order made on 26/11/2020

5/5

Excellent produit que j'utilise couramment comme relai avec la box eedomus pour piloter des volets, le portail et maintenant la pompe à chaleur avec le thermostat. Au top

Did you find this helpful? Yes 0 No 0

Anonymous customer published the 26/11/2020 following an order made on 25/10/2020

4/5

Un côté un peu gros pour rentrer sous un interrupteur, j'ai préféré le monter sur ma chaudière.

Did you find this helpful? Yes 0 No 0

Anonymous customer published the 03/09/2020 following an order made on 11/08/2020

5/5

RAS- FIBARO quoi !

Did you find this helpful? Yes 0 No 0

Anonymous customer published the 22/08/2020 following an order made on 07/08/2020

5/5

pas de pb avec ces modules

Did you find this helpful? Yes 0 No 0

Anonymous customer published the 06/08/2020 following an order made on 18/07/2020

5/5

Conforme

Did you find this helpful? Yes 0 No 0

Anonymous customer published the 27/07/2020 following an order made on 12/07/2020

5/5

Très bien

Did you find this helpful? Yes 0 No 0

×

The reset procedure restores the module to its factory settings, which means that all information about the Z-Wave controller and user configuration will be deleted.

Resetting the module is not the recommended method to remove the device from the Z-Wave network. Use the reset procedure only if the primary controller is missing or inoperative.

1. Press and hold the maintenance button to access the menu.

2. Release the button when the module LED turns yellow.

3. Quickly press the button to confirm.

4. After a few seconds, the module will be restarted, which is signaled by a red LED.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

The FGS-214 and FGS-224 modules have an integrated Z-Wave network main controller range tester.

To make the Z-Wave range test possible, the module must be included with the Z-Wave controller. The tests can stress the network, so it is recommended to perform the test only in special cases.

To test the main controller's range:

1. Press and hold the maintenance button to access the menu.

2. Release the button when the device turns magenta.

3. Quickly press the button to confirm.

4. The visual indicator will indicate the range of the Z-Wave network (range signaling modes described below).

5. To exit the Z-Wave range test, short press the button.

Z-Wave Range Tester Signaling Modes:

Visual indicator flashing green - the device is attempting to establish direct communication with the main controller. If a direct communication attempt fails, the device will attempt to establish routed communication, via other modules, which will be indicated by a visual indicator flashing yellow.

Bright green visual indicator - the device communicates directly with the main controller.

Visual indicator flashing yellow - the device is trying to establish routed communication with the main controller via other modules (repeaters).

Bright yellow visual indicator - the device communicates with the main controller via the other modules. After 2 seconds, the device will retry to establish direct communication with the main controller, which will be indicated by a visual indicator flashing green.

Visual indicator flashing purple - device is communicating at the maximum distance of the Z-Wave network. If the connection is successful, it will be confirmed with a yellow glow. It is not recommended to use the device at the limit of range.

Glowing visual indicator - the device cannot connect directly to the main controller or through another Z-Wave network device (repeater).

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

To remove the module from the Z-Wave network:

1. Power up the module.

2. Put the main controller in exclusion mode (see controller manual).

3. Quickly press the maintenance button three times.

4. The LED will start flashing yellow, wait for the deletion process to complete.

5. Successful exclusion will be confirmed by Z-Wave controller message and red LED color.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

To add the module to your Z-Wave network manually:

1. Power up the module.

2. Put the main controller in inclusion mode (Secure / Non-Secure Mode) (see controller manual).

3. Quickly three times press the button connected to S1/S2 or the maintenance button.

4. The LED will start flashing yellow, wait for the inclusion process to complete.

5. If you are performing a secure inclusion, enter the underlined part of the DSK (label at the bottom of the box).

6. Inclusion will be confirmed by Z-Wave controller message and LED:

Green - passed (unsecured, S0, S2 unauthenticated),

Magenta - passed (Security S2 authenticated),

Red - not successful.

 

To add the module to the Z-Wave network using SmartStart:

1. To use SmartStart, your controller must support Security S2 (see controller manual).

2. Enter the full DSK code into your controller. If your controller is able to scan a QR code, scan the QR code placed on the box or label of the device.

3. Power up the module.

4. Wait for the inclusion process to start (may take a few minutes), which is signaled by the yellow LED flashing.

5. Inclusion will be confirmed by Z-Wave controller message and LED:

Green - passed (unsecured, S0, S2 unauthenticated),

Magenta - passed (Security S2 authenticated),

Red - not successful.

Does this answer your question?
Yes (0)
No (0)
Sorry about that
How can we improve it?
Submit
Thanks
Your feedback helps improve this answer for everyone.

You might also like