• Refurbished
  • -20%
EUTONOMY - Adapter DIN for Fibaro Single Switch 2 FGS-213 with buttons
search
  • EUTONOMY - Adapter DIN for Fibaro Single Switch 2 FGS-213 with buttons
  • EUTONOMY - Adapter DIN for Fibaro Single Switch 2 FGS-213 with buttons
  • EUTONOMY - Adapter DIN for Fibaro Single Switch 2 FGS-213 with buttons
  • EUTONOMY - Adapter DIN for Fibaro Single Switch 2 FGS-213 with buttons
  • EUTONOMY - Adapter DIN for Fibaro Single Switch 2 FGS-213 with buttons
  • EUTONOMY - Adapter DIN for Fibaro Single Switch 2 FGS-213 with buttons
  • EUTONOMY - Adapter DIN for Fibaro Single Switch 2 FGS-213 with buttons
  • EUTONOMY - Adapter DIN for Fibaro Single Switch 2 FGS-213 with buttons
  • EUTONOMY - Adapter DIN for Fibaro Single Switch 2 FGS-213 with buttons
  • EUTONOMY - Adapter DIN for Fibaro Single Switch 2 FGS-213 with buttons

EUTONOMY - Adapter DIN for Fibaro Single Switch 2 FGS-213 with buttons



RECO-EUT_S213
Refurbished

Product taken back under the right of withdrawal.
The product is in good general condition.
It has been inspected, cleaned by a technician, in order to meet the original characteristics of the manufacturer. It is supplied with the accessories essential to its operation.

Domadoo warranty: 1 year.

€46.80
€37.44 Tax included Save 20%

The euFIX S213 Adapter is used to install the Fibaro® Switch FGS-213 module on DIN TH35 type rail in the electrical switchboard.


1 Product available
Quantity

 

Security guarantees

 

Shipping Policy

The euFIX S213 Adapter is used to install the Fibaro® Switch FGS-213 module on DIN TH35 type rail in the electrical switchboard.

The euFIX S213 Adapter consists of the case and the base board, where the FGS-213 module is mounted. The dimensions of the case are appropriate for a standard DIN TH35 type rail.

The base board contains a set of screw terminals, where all the wires (power supply, input and output signals, control push- buttons) can be safely connected.

The front panel of the case contains two diagnostics micro-push-buttons S1 & S2, which can be used to control the module, to register the module within the Z-Wave system or to remove it from the system without opening the adapter's case. 

FEATURES :

  • DIN adapter for Fibaro Switch FGS-213 with push-buttons
  • Used to install the Switch FGS-213 module on DIN TH35/TS35 type rail in the electrical switchboard
  • Free location on the label to locate the controlled line
  • Micro-push-buttons S1 & S2 used for control, inclusion or exclusion of the module within the Z-Wave system

TECHNICAL SPECIFICATIONS :

  • Supply voltage: 230 V AC +/-10%, 50–60Hz 
  • Load power: max 8A
  • Dimensions: 34.8 x 87.3 x 64.7 mm
  • Width in TE units: 2 TE modules
  • Conductor wires cross section: max. 2.5 mm2 
  • Maximum length of wires connected to Sx, S1, S2 inputs: 20m
  • Operating temperature: 0 °C to +50 °C
  • Relative humidity: ≤90 %, no condensation
  • Directives:
    • LVD 2014/35/EC
    • RoHS 2011/65/EU 



RECO-EUT_S213
1 Item

Data sheet

Type
Accessory
Refurbished

You might also like

8 other products in the same category: