

The Aqara DJT11LM sensor has a built-in high-precision accelerometer.
(à modifier dans le module "Réassurance")
(à modifier dans le module "Réassurance")
The Aqara DJT11LM sensor has a built-in high-precision accelerometer, when the object is abnormally vibrated, tilted or dropped, the abnormal situation is reported to the gateway, and send the message to the mobile phone app, so that you can know in time.
This sensor provides high, medium and low three-speed sensitivity, you can freely adjust the appropriate gear position according to different installation environments, improve detection sensitivity, and effectively reduce false alarm.
All notifications can be set up to alert your smart phone via the Aqara (Aqara Home) APP so no matter where you are you can have peace of mind that your property is safe and secure.
Use the Aqara Vibration Sensor DJT11LM in combination with other Aqara Smart Home Eco System products to experience a truly SMART HOME!
FEATURES :
TECHNICAL SPECIFICATIONS :
Data sheet
David L. published the 14/09/2022 following an order made on 09/09/2022
Très bon produit ont peut régler la sensibilité que sur l app aqara 100 % compatible home kit.
William G. published the 07/04/2022 following an order made on 31/03/2022
Conforme aux attentes
Christian F. published the 18/03/2022 following an order made on 11/03/2022
bon produit
Pierre G. published the 15/02/2022 following an order made on 01/02/2022
Détecte bien les vibrations. Par contre ne se déclenche pas forcément quand le mouvement est un peu doux.
Olivier B. published the 29/01/2022 following an order made on 18/01/2022
Fonctionne parfaitement sous home assistant
Pierre P. published the 24/01/2022 following an order made on 18/01/2022
parfait
Anonymous customer published the 14/05/2021 following an order made on 30/04/2021
Fonctionne très bien, installés sur un produit "sensible", j'en ai pris deux pour prévenir des déclenchements intempestifs ou non détectés mais un seul fait l'affaire, la détection est très fiable.
Anonymous customer published the 20/03/2021 following an order made on 06/03/2021
Efficace
Anonymous customer published the 20/03/2021 following an order made on 10/02/2021
Produits aqara relativement faciles à connecter mais relevés difficiles à interpréter et très mal documentés. De plus , la rotation sur une porte n'est pas un des axes prévus donc seule la vibration sert pour ce cas de figure.
After connecting the Aqara vibration sensor to the hub, press the reset button on the vibration sensor once in the desired location before installation. If you hear the hub prompts "normal link confirmed", that means the location is suitable for installation. If you don't hear a voice prompt, adjust the location of the vibration sensor and try again.
The Aqara vibration sensor uses a CR2032 button battery. When replacing the battery, insert a coin into the groove of the battery cover and turn it counterclockwise to release the cover. Remove the old battery and insert a new CR2032 coin cell battery and tighten the battery cover.
Open the Aqara Home app and navigate to the Vibration Sensor page. Click "..." in the upper right corner, then select "Adjust vibration sensitivity". You can then choose the appropriate sensitivity and press OK. Finally, press the reset button on the device once to complete the setup. If the configuration fails, please try again following the same steps.
Due to the different materials, thicknesses and structures of different objects, the same action or force applied to these objects will be registered differently by the vibration sensor. Therefore, sometimes it is easy to trigger while other times not. You can increase or decrease the sensitivity of the vibration sensor via the Aqara Home app.
The “vibration detected” event is triggered once per minute. If the event was triggered, it will not be triggered for the next minute. If the vibrations persist, the event will trigger again one minute later.
No, the Aqara vibration sensor must work with a home automation hub or box. When a vibration is detected, the hub will trigger sound and light alarms. Alert notification will be sent to phone or linked to control other smart accessories (via automation).
The Aqara vibration sensor detects vibration, tilt and drops.
You might also like